Receiver Buyers' Guide

Home Cinema Knowledgebase

Blu-Ray Advanced Guide
DLP TV Advanced Guide
AV Processors Guide
Home Cinema Amplifier
Flat Speakers
LCD Monitors
Home Theater Speakers
Setting up a Home Cinema
Home Cinema Terminology
HT Speaker Stands
HT Equipment Racks
Home Theater Seating
Home Theater Design/Setup
Home Theater Design
Home Theater Room Setup
HT audio setup
Submit Your Review
Link to us
Favourite Home Theater Websites
Home Theater Information/Articles
Home Theater Wiring

Receiver Basics:

Next to choosing your loudspeakers, selecting the right receiver, be it a Dolby Digital/dts 5.1-channel surround-sound A/V model or a simple

2-channel stereo unit, is almost as important because you have to contemplate future needs and how much power and versatility you're willing to pay for.

The receiver serves as the control unit and the amplification center for your entire system (it's a "receiver" because it contains a built-in AM/FM radio tuner). If it lacks an AM/FM tuner, it would be an "integrated amplifier," or just plain "amp," for short. In any case, the receiver and its remote control let you select which source to listen to (CD player, FM tuner, tape deck, VCR, or DVD player) or watch (if it's an audio-video receiver). When you press "CD" on the remote, the receiver internally switches its amplifiers to the incoming signal from your CD player, passes those signals through its control section (tone, balance and volume controls), then to its built-in amplifiers and sends the greatly strengthened audio signals to your speakers (and the accompanying video signal to your TV, if you selected "DVD" or "VCR" on an A/V receiver).

First, however, you must choose whether to get a simple stereo receiver that has two internal amplifiers to drive a pair of speakers, or instead, an A/V surround-sound unit that will have a minimum of five internal amplifiers to drive five speakers in your room: the left and right main speakers up front, a center-channel speaker atop your TV, and two surround speakers on the side walls. The sixth or ".1" channel, as in "5.1," is for just deep bass and low-frequency soundtrack effects. That Low-Frequency Effects (LFE) ".1" channel is sent to your subwoofer, which almost always has its own internal amplifier. Surround-sound A/V receivers also have internal digital decoders to sort out the DVD player's Dolby Digital or dts digital 5.1-channel soundtrack.

By comparison, stereo receivers are blessedly simple-just two internal amplifiers, no surround sound circuitry, and two pairs of speaker output connectors for the left and right channels. That still appeals to lots of buyers. However, prices of surround-sound 5.1-channel A/V receivers have become so competitive that they cost little more than a basic 2-channel stereo model. So consider very carefully whether or not you're planning a home theater system for a future (or bigger) home or if you want plain ol' vanilla stereo. Moreover, if you think that at some point in the future, you might be persuaded by the sheer pleasure of surround sound then now is the time to go for a multi-channel A/V receiver.

The rated power output of the receiver's internal amplifiers, stated in watts per channel into 8 ohms, will ultimately determine the unit's selling price. The more power you buy, the more costly the receiver. But "solid-state" (transistor) amplifiers are very economical. You can find stereo receivers with 80 or 100 watts per channel for as little as $300. A/V surround receivers with similar power start at the $400 mark. Don't go cheap on the power: the greatest source of damage to speakers is using too small amplifiers to drive speakers at high volumes, especially when you might "crank it up" at a party. The amp runs out of watts, distorts, and the distorted signal burns out tweeters or woofers in seconds. And one basic truth most consumers do not understand when they are shopping for amps and speakers: smaller speakers generally require more power-not less-to produce realistic volume levels than big speakers do because they use smaller woofers and are less efficient.

In all but very large living rooms or those with cathedral ceilings and volumes of 6,000 to 7,500 cubic feet, receivers with 80 to 100 watts output per channel to all five channels will be sufficient. Those modest little 35-watt amplifiers may be okay for a den or a dorm but they just can't cut it in an average living room unless you're going to listen at background levels. And background levels are strictly low fidelity - we don't go to a concert and tell the musicians, "Hey, play really quietly!"

By Alan Lofft Sponsored by Axiom Audio

Contact Us | Cinema Eye | Add Home-Theater-Reviews to your site! | ©2008 Home-Theater-Reviews.co.uk | XML Sitemap | Sitemap |